Audi Q7: Fuse assignment - cockpit
Fig. 194 Driver side cockpit: fuse panel with plastic bracket
Fuse panel (1) (black)
- Convenience access and start authorization
control module
- Audi phone box, USB connection
- Head-up display
- Audi music interface, USB connection
- Steering column lock
- Upper/lower display
- Instrument cluster
- DVD drive
- Light switch, switch module
- Steering column electronics
- Volume control
- MMI Infotainment system control module
- Steering column adjustment
- Steering wheel heating
Fuse assignment - luggage compartment
Fig. 195 Left side of the luggage compartment: fuse panel with plastic clip
Fig. 196 Left side of the luggage compartment: fuse panel
with plastic clip (plug-in hybrid drive*)
Fuse panel (1) (black)
- High-voltage heating, thermomanagement
- Air suspension/suspension control
- Automatic transmission control module
- Rear seat heating, rear climate control system
controls
- Third row seat adjustment
- Convenience system control module, left
tail light
- Front belt tensioner on driver's side
- Luggage compartment lid lock, fuel filler door, luggage compartment
cover
- Luggage compartment lid control module
Fuse panel (2) (red)
- Rear climate control system blower
- Sound-amplifier
- Exhaust treatment, sound actuator
- Rear climate control system control panel
- Right trailer hitch light
- Trailer hitch positioning motor
- Trailer hitch release
- Left trailer hitch light
- Trailer hitch socket
- Allroad sport differential
- Exhaust treatment
- Driver's side rear safety belt tensioner
Fuse panel (3) (brown)
- Driver assistance systems control module
- Audi phone box
- Right lumbar support
- Side assist
- Tire pressure monitoring system
- Exterior antenna
- Auxiliary heating radio receiver, tank module
- TV tuner, data exchange and telematics control module
- Convenience access and start authorization control module
- Garage door opener
- Rearview camera, peripheral cameras
- Convenience system control module, right headlights and tail lights.
However, if a light bulb
tail light
- Passenger's side rear safety belt tensioner
- Grant belt tensioner on front passenger's side
Fuse panel (4) (red)
- Active roll stabilization
- High-voltage battery
- High-voltage battery coolant pump
- Power electronics control module
- Brake booster
- Voltage converter
- Engine start
- Climate control system compressor
- Auxiliary battery control module
- High-voltage battery
- Charging system
- Auxiliary heating and air conditioning radio receiver
- Thermal management, coolant pumps
- Thermomanagement control module
Fuse panel (5) (brown)
- Front seat heating
- Exhaust treatment
- Rear seat heating, rear climate control system controls
- Exhaust treatment
Bulbs
Replacing bulbs
Audi recommends having a bulb replaced by an
authorized Audi dealer or authorized Audi Service
Facility in cases of doubt. These facilities have
the correct tools and replacement parts as well
as the required technical knowledge.
LED lights*
Your vehicle is equipped with maintenance-free
headlights and tail lights. However, if a light bulb
needs to be replaced, please contact an authorized Audi dealer or authorized
Audi Service Facility.
WARNING
If you still would like to try replacing the
bulbs in your vehicle yourself, read the warnings
regarding working in the engine compartment
in General information.
Note
Make sure the covers are fitted correctly on
the headlight and tail light so that no water
will leak in from the outside and the light
function will not be impaired.
READ NEXT:
You can find information about responsibility for
data protection in the MMI.
Applies to: MMI: Select on the home screen: SETTINGS
> General > Legal notes > About Audi
connect.
Image recordi
SEE MORE:
Outer CV Joint, Removing
- Clamp the drive axle in a vise with protective covers.
- Open both clamping sleeves and remove protective joint boot
from outer joint.
- Drive out the CV joint from the drive axle with a copper or
brass mandrel -A- on the inner
ring.
- Remove joint a
General Description
The secondary air injection system sends air into the
exhaust using passages in the cylinder head. This extra air
injection takes place using the Secondary Air Injection Pump
Motor -V101- that is powered by the Secondary Air Injection Pump
Relay -J299- on a cold-start of the