Audi Q7: Safety Precautions
Safety Precautions when Working on Vehicle
Pay Attention to the Following to Avoid Personal Injury and
Vehicle Damage:
WARNING
Risk of injury and accident by accidentally engaging
a selector lever position with the engine running.
Shift the transmission into "P" and set the parking
brake to lock the electro-mechanical parking brake
before working on a running engine.
Danger of poisonous exhaust gas with the engine
running.
When engine is running, an exhaust extracting system
must always be connected to the exhaust system.
Risk of injury through the radiator fan turning on
automatically.
Disconnect the connectors before working near the
fan shroud.
To Prevent Personal Injury, Damage or Destruction of
Electrical and Electronic Components, Observe the Following:
- Only connect and disconnect test equipment when the ignition
is off.
Caution
Risk of destroying electronic components when
disconnecting the battery.
- Follow the steps when disconnecting the battery.
- Only disconnect the battery when the ignition is
turned off. Refer to
→ Electrical Equipment; Rep. Gr.27; Battery; Battery,
Disconnecting and Connecting.
Safety Precautions when Working on Vehicles with Start/Stop System
Pay Attention to the Following when Working on Vehicles with
A Stop/Start System:
WARNING
Risk of injury if the engine starts automatically in
vehicles with a Start/Stop System.
- For vehicles with an activated Start/Stop System
(recognizable from a notification in the instrument
cluster), the motor can be started automatically if
needed.
- Make sure the Start/Stop system is deactivated when
working on the vehicle (turn off ignition and turn the
ignition back on if needed).
Safety Precautions during Road Test with Testing Equipment
If Testing Equipment Must Be Used During a Road Test,
Observe the Following:
WARNING
There is a risk of an accident due to distractions
and improperly secured testing equipment.
The front passenger airbag poses a risk if it
deploys during an accident.
- Operating testing equipment while driving is a
distraction.
- Testing equipment that is not secured properly
increases the risk of personal injury.
Always secure testing equipment on the rear seat
with a strap and have a second person on the rear seat
operate it.
Safety Precautions when Working on Subframe
Note the Following whenever Working on the Subframe:
Caution
Risk of damaging the suspension components.
- Do not rest the vehicle on its wheels if the
subframe mount, the steering gear or the subframe
crossbrace are not installed correctly.
- Supporting the vehicle on the subframe or the
subframe crossbrace, (for example, by a floor jack or
similar device) is not permitted.
Safety Precautions when Tow Starting and Towing
Caution
Risk of destroying the transmission.
- If the vehicle needs to be towed, make sure the
selector lever is in "N" or the parking lock must be
emergency released. Refer to
→ Chapter "Emergency Release from P".
- The vehicle may not be towed farther than 50 km (31
miles) and not faster than 50 km/h (31 mph).
Note
The engine cannot be tow started, for example, if the
battery is too weak or if the starter is not working.
READ NEXT:
Guidelines for Clean Working Conditions
Thoroughly clean the connection points and the surrounding
area before loosening.
Clean the transmission and transmission components using
Cleaning Solutio
Capacities
Capacities, ATF Area in the Transmission
Caution
There is a risk that the transmission could
malfunction or fail.
Only use the ATF available as a replacement part
with the 0D5 a
Overview - Torque Converter
1 - Torque Converter
Refer to the Parts Catalog for the allocation to the transmission.
Removing and installing. Refer to
→ Chapter "Torque Converter,
SEE MORE:
Services
Applies to: vehicles with Audi connect vehicle control
Using Audi connect vehicle control services, you
can perform tasks such as viewing data about
your vehicle or control vehicle functions remotely.
You can view and use services available for your
vehicle at my.audi.com or through the my
Removing
- Turn the light switch to position "0".
- Remove the light switch trim. Refer to
→ Body Interior; Rep. Gr.70; Instrument Panel; Light Switch
Trim, Removing and Installing.
- If equipped, remove the bolts -1 and
4-.
- Release the retainers in the dire